WEEK 7 FYP SEMESTER 2


Objective

To overcome and rebuild the previous unsuccessful PIR sensor.



Activity

In this time have make the final adjustment by change PIR sensor to PIR module sensor. This module is 100% been amplified the output from PIR sensor. The module shown below :

   This PIR module may be integrated  to the other circuit with which from the circuit done on lab session for subject ACTUATOR. The circuit is used astable 555 timer circuit. The circuit will shown at below :

The lab session circuit, the pin out 4 for 555 timer is connected to supply which is consistent input to make the output continuously. It make indicator buzzer to switch on continuously. Therefore, pin out 555 timer is connected to output PIR module to receive output when PIR module is detect motion.

WEEK 6 FYP SEMESTER 2


Objective

To overcome the previous unsuccessful PIR sensor circuit.


Activity

The previous PIR sensor circuit is don't display output to LED then adjustment are make it the construction back the circuit to new PIR sensor circuit is follow circuit below :

In this circuit, their is adjustment for the circuit and follow the example circuit to try to overcome problem before. The circuit don't use amplifier to convert output. Therefore direct take output from PIR to create the output there is buzzer. The buzzer is the indicator for this circuit.

WEEK 5 FYP SEMESTER 2

Objective 

To construct and testing the PIR sensor circuit


Activity


The construction for the PIR sensor circuit is follow circuit below:

The construct and testing using PIR sensor. Without using PIR module. This circuit is using amplifier is to convert the PIR sensor output to suitable output in voltage. Using relay 12V to switch on to deliver output active high or active low to LED. Free willing diode that connected between relay is to prevent transistor receive continuous supply from relay. It may recycle back within the relay only.

WEEK 1 - 4 FYP SEMESTER 2


Objective

To create the simulation coding to run temperature circuit
To complete and test the simulation coding until success



Activity

The coding simulation is used software MPLAB. The MPLAB is used cause of previous project (Diploma Project) also doing the same software. How to build and compiling this circuit is been made it. The different from the previous project is range to detect temperature. The previous is used range from 35C to 40C. Not suitable to the premature baby. Therefore, changes is make it by change the range from 25C until 27C which is 25C temperature sensor B and 27C temperature sensor A. Below show how to create and make the simulation:

WEEK 12

OBJECTIVE

To prepare of proposal report



ACTIVITY

The proposal is create by discussion with the supervisor to make sure flow of proposal follow the guideline. The commend and recommendation from assessor from presentation day is take a note to improve the proposal writing. The proposal is using computer which is Microsoft word. Proposal is more detail from presentation slide. It consist all main title from presentation but more elaborate in word.

WEEK 11

OBJECTIVE 

To find example of circuit for project.



ACTIVITY

The circuit that was for temperature are already have from previous diploma project,but adjustment will take from sensor to RF circuit. Rf is using RF module. For motion sensor is using example circuit that will present to used into project. The circuit take from internal only the guideline to create the project hardware and also software.

WEEK 10

OBJECTIVE
To preparation for proposal presentation.


ACTIVITY

The proposal is in progress. Before submitted the proposal report, proposal presentation will take action before it. Preparing of presentation is like summary or simplify from whole proposal report. The main of presentation is to explain to assessors about our project and take the suggestion and also improver into our project. The flow of presentation is take the main point inside proposal report which is Objective, Abstract, Introduction, Problem Statement, Problem Solution, Methodology, Lecturer Review, Benefit, Work Plan, Budget and Conclusion. The preparing of presentation happen in a week. Before presentation, meet with supervisor to ask and show slide presentation. After adjustment and correction, the presentation slide completed. Date of presentation day, Friday 22 November 2013 from 2PM – 5 PM at Gemilang Hall, Unikl BMI. The assessors which is Sir SHAH RIZAILLI and DR SABRY. Feedback from assessor is taken to improve abd make propasl report more reasonable.